HD vervangen in cubestation

[Kris]

Ik ben perfect geholpen door Bjorn van MHD die een defecte schijf (garantie) heeft vervangen.

Deze kreeg ik per post vandaag.

Nu heb ik deze in de CS gestopt maar zie ik dat mijn raid5 configuratie degraded is en zie ik de 4de disk niet in het overzicht. Wat moet ik doen om deze disk te laten zien en weer te laten syncen in de configuratie??

Thnx.

[mdamen]

In principe moet die disk meteen zichtbaar zijn en kan je daarmee je raid-5 array repareren.
Heb je telnet/SSH toegang tot je syno? Zo ja, kan je dan eens de output van het volgende commando hier posten:

Code: [Selecteer]

dmesg
En ook van de volgende commando's:

Code: [Selecteer]

dmesg | grep "sda"
dmesg | grep "sdb"
dmesg | grep "sdc"
dmesg | grep "sdd"

En als laatste van het volgende commando:

Code: [Selecteer]

mdadm --query --detail /dev/md2

Controleer voor de zekerheid ook nog even de kabels... je weet maar nooit :-)

[Kris]

Telnet / SSH kom ik er niet op. Krijg de melding dat de host de verbinding dichtgooit.

[J@n]

Hi Kris,

Voor Telnet / SSH moet je een "firmware-update" uitvoeren. Die kun je hier downloaden: http://www.synology.com/enu/support/download.php#Patches In principe kun je dat zonder gevaar voor je RAID set doen.

Enne oh ja.....Als je toegang hebt na de update en je wil de commando's van Maarten invoeren? Log dan in de Telnet sessie in als root. Als je dat niet doet krijg je geen output. Tis maar dat je het weet

Greetz,

J@n

[Kris]

Okay, had hij er maar bijgezegd dat ik een firmware update diende uit te voeren.

Ga ik gelijk doen. Bedankt Jan.
Verder, wat is het password van de root? Is dat hetzelfde van admin? Ik dacht het niet....
[edit]
Even zoekfunctie gebruikt, wel dus
[/edit]

[Kris]

Heb misschien wel wat dingen dubbel geplakt, maar niet alle output ging telkens mee in het clipboard.
Ik haal er zelf uit de de nieuwe HD niet herkend wordt. Had zelfs een paar keer de HD omgewisseld met een andere stekker, maar toen was ik bijv. disk 3 kwijt....

Code: [Selecteer]

Cervus login: root
Password:


BusyBox v1.1.0 (2008.03.12-11:49+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

Cervus> dmesg
A
  Type:   Direct-Access                      ANSI SCSI revision: 05
drivers/scsi/sd.c (1707) Internal disk with bus id: 0
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
drivers/scsi/sd.c (1707) Internal disk with bus id: 1
SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sdb: drive cache: write back
 sdb: sdb1 sdb2 sdb3
sd 1:0:0:0: Attached scsi disk sdb
drivers/scsi/sd.c (1707) Internal disk with bus id: 2
SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sdc: drive cache: write back
SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sdc: drive cache: write back
 sdc: sdc1 sdc2 sdc3
sd 2:0:0:0: Attached scsi disk sdc
physmap flash device: 1000000 at ff000000
CFI: Found no phys_mapped_flash device at location zero
DS406-0: Found 1 x16 devices at 0x0 in 8-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
DS406-0: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Searching for RedBoot partition table in DS406-0 at offset 0x3f0000
6 RedBoot partitions found on MTD device DS406-0
DS406 flash bank 0: Using RedBoot partition definition
Creating 6 MTD partitions on "DS406-0":
0x00300000-0x00340000 : "RedBoot"
0x00000000-0x00200000 : "zImage"
0x00200000-0x00300000 : "rd.gz"
0x00340000-0x00350000 : "vendor"
vender Mac1 checksum error ucSum:0x00 Buf:0x00 Sum:0.
Vender partition MacNum:1 retlen:64
No Serial Number or Serial Number checksum error ucSum:0xf6 Buf:0xff Sum:2550.
0x00350000-0x00370000 : "RedBoot Config"
0x003f0000-0x00400000 : "FIS directory"
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid6: int32x1     24 MB/s
raid6: int32x2     40 MB/s
raid6: int32x4     60 MB/s
raid6: int32x8     75 MB/s
raid6: using algorithm int32x8 (75 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: measuring checksumming speed
   8regs     :   474.000 MB/sec
   8regs_prefetch:   386.000 MB/sec
   32regs    :   489.000 MB/sec
   32regs_prefetch:   409.000 MB/sec
raid5: using function: 32regs (489.000 MB/sec)
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: considering sda1 ...
md:  adding sda1 ...
md: sda2 has different UUID to sda1
md: sda3 has different UUID to sda1
md:  adding sdb1 ...
md: sdb2 has different UUID to sda1
md: sdb3 has different UUID to sda1
md:  adding sdc1 ...
md: sdc2 has different UUID to sda1
md: sdc3 has different UUID to sda1
md: created md0
md: bind<sdc1>
md: bind<sdb1>
md: bind<sda1>
md: running: <sda1><sdb1><sdc1>
raid1: raid set md0 active with 3 out of 4 mirrors
md: considering sda2 ...
md:  adding sda2 ...
md: sda3 has different UUID to sda2
md:  adding sdb2 ...
md: sdb3 has different UUID to sda2
md:  adding sdc2 ...
md: sdc3 has different UUID to sda2
md: created md1
md: bind<sdc2>
md: bind<sdb2>
md: bind<sda2>
md: running: <sda2><sdb2><sdc2>
raid1: raid set md1 active with 3 out of 4 mirrors
md: considering sda3 ...
md:  adding sda3 ...
md:  adding sdb3 ...
md:  adding sdc3 ...
md: created md2
md: bind<sdc3>
md: bind<sdb3>
md: bind<sda3>
md: running: <sda3><sdb3><sdc3>
raid5: device sda3 operational as raid disk 0
raid5: device sdb3 operational as raid disk 1
raid5: device sdc3 operational as raid disk 2
raid5: allocated 4212kB for md2
raid5: raid level 5 set md2 active with 3 out of 4 devices, algorithm 2
RAID5 conf printout:
 --- rd:4 wd:3
 disk 0, o:1, dev:sda3
 disk 1, o:1, dev:sdb3
 disk 2, o:1, dev:sdc3
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
ds406_synobios: module license 'Synology Inc.' taints kernel.
synobios: load, major number 201
Brand: Synology
Model: CS-406
synobios: unload
kjournald starting.  Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on md2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem).
Trying to move old root to /initrd ... okay
Freeing unused kernel memory: 124k init
Adding 393464k swap on /dev/md1.  Priority:-1 extents:1 across:393464k
NET: Registered protocol family 5
NTFS driver 2.1.27 [Flags: R/O DEBUG MODULE].
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
sd 2:0:0:0: Attached scsi generic sg2 type 0
usbcore: registered new driver usbfs
usbcore: registered new driver hub
usbcore: registered new driver snd-usb-audio
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
sk98lin: Network Device Driver v8.41.2.3
(C)Copyright 1999-2006 Marvell(R).
eth0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
      PrefPort:A  RlmtMode:Check Link State
synobios: load, major number 201
Brand: Synology
Model: CS-406
eth0: network connection up using port A
    speed:           100
    autonegotiation: yes
    duplex mode:     full
    flowctrl:        symmetric
    irq moderation:  disabled
    scatter-gather:  enabled
    tx-checksum:     enabled
    rx-checksum:     enabled
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on md2, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
ehci_hcd 0000:00:0e.2: EHCI Host Controller
ehci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0e.2: irq 17, io mem 0xbfffcf00
ehci_hcd 0000:00:0e.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd 0000:00:0e.0: OHCI Host Controller
ohci_hcd 0000:00:0e.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0e.0: irq 17, io mem 0xbfffe000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ohci_hcd 0000:00:0e.1: OHCI Host Controller
ohci_hcd 0000:00:0e.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:0e.1: irq 17, io mem 0xbfffd000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v2.3
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Cervus> dmesg


raid6: int32x4     60 MB/s
raid6: int32x8     75 MB/s
raid6: using algorithm int32x8 (75 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: measuring checksumming speed
   8regs     :   474.000 MB/sec
   8regs_prefetch:   386.000 MB/sec
   32regs    :   489.000 MB/sec
   32regs_prefetch:   409.000 MB/sec
raid5: using function: 32regs (489.000 MB/sec)
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: considering sda1 ...
md:  adding sda1 ...
md: sda2 has different UUID to sda1
md: sda3 has different UUID to sda1
md:  adding sdb1 ...
md: sdb2 has different UUID to sda1
md: sdb3 has different UUID to sda1
md:  adding sdc1 ...
md: sdc2 has different UUID to sda1
md: sdc3 has different UUID to sda1
md: created md0
md: bind<sdc1>
md: bind<sdb1>
md: bind<sda1>
md: running: <sda1><sdb1><sdc1>
raid1: raid set md0 active with 3 out of 4 mirrors
md: considering sda2 ...
md:  adding sda2 ...
md: sda3 has different UUID to sda2
md:  adding sdb2 ...
md: sdb3 has different UUID to sda2
md:  adding sdc2 ...
md: sdc3 has different UUID to sda2
md: created md1
md: bind<sdc2>
md: bind<sdb2>
md: bind<sda2>
md: running: <sda2><sdb2><sdc2>
raid1: raid set md1 active with 3 out of 4 mirrors
md: considering sda3 ...
md:  adding sda3 ...
md:  adding sdb3 ...
md:  adding sdc3 ...
md: created md2
md: bind<sdc3>
md: bind<sdb3>
md: bind<sda3>
md: running: <sda3><sdb3><sdc3>
raid5: device sda3 operational as raid disk 0
raid5: device sdb3 operational as raid disk 1
raid5: device sdc3 operational as raid disk 2
raid5: allocated 4212kB for md2
raid5: raid level 5 set md2 active with 3 out of 4 devices, algorithm 2
RAID5 conf printout:
 --- rd:4 wd:3
 disk 0, o:1, dev:sda3
 disk 1, o:1, dev:sdb3
 disk 2, o:1, dev:sdc3
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
ds406_synobios: module license 'Synology Inc.' taints kernel.
synobios: load, major number 201
Brand: Synology
Model: CS-406
synobios: unload
kjournald starting.  Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on md2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem).
Trying to move old root to /initrd ... okay
Freeing unused kernel memory: 124k init
Adding 393464k swap on /dev/md1.  Priority:-1 extents:1 across:393464k
NET: Registered protocol family 5
NTFS driver 2.1.27 [Flags: R/O DEBUG MODULE].
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
sd 2:0:0:0: Attached scsi generic sg2 type 0
usbcore: registered new driver usbfs
usbcore: registered new driver hub
usbcore: registered new driver snd-usb-audio
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
sk98lin: Network Device Driver v8.41.2.3
(C)Copyright 1999-2006 Marvell(R).
eth0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
      PrefPort:A  RlmtMode:Check Link State
synobios: load, major number 201
Brand: Synology
Model: CS-406
eth0: network connection up using port A
    speed:           100
    autonegotiation: yes
    duplex mode:     full
    flowctrl:        symmetric
    irq moderation:  disabled
    scatter-gather:  enabled
    tx-checksum:     enabled
    rx-checksum:     enabled
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on md2, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
ehci_hcd 0000:00:0e.2: EHCI Host Controller
ehci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0e.2: irq 17, io mem 0xbfffcf00
ehci_hcd 0000:00:0e.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd 0000:00:0e.0: OHCI Host Controller
ohci_hcd 0000:00:0e.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0e.0: irq 17, io mem 0xbfffe000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ohci_hcd 0000:00:0e.1: OHCI Host Controller
ohci_hcd 0000:00:0e.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:0e.1: irq 17, io mem 0xbfffd000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v2.3
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Cervus> dmesg | grep "sda"
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
md: considering sda1 ...
md:  adding sda1 ...
md: sda2 has different UUID to sda1
md: sda3 has different UUID to sda1
md: sdb2 has different UUID to sda1
md: sdb3 has different UUID to sda1
md: sdc2 has different UUID to sda1
md: sdc3 has different UUID to sda1
md: bind<sda1>
md: running: <sda1><sdb1><sdc1>
md: considering sda2 ...
md:  adding sda2 ...
md: sda3 has different UUID to sda2
md: sdb3 has different UUID to sda2
md: sdc3 has different UUID to sda2
md: bind<sda2>
md: running: <sda2><sdb2><sdc2>
md: considering sda3 ...
md:  adding sda3 ...
md: bind<sda3>
md: running: <sda3><sdb3><sdc3>
raid5: device sda3 operational as raid disk 0
 disk 0, o:1, dev:sda3
Cervus> dmesg | grep "sdb"
SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sdb: drive cache: write back
 sdb: sdb1 sdb2 sdb3
sd 1:0:0:0: Attached scsi disk sdb
md:  adding sdb1 ...
md: sdb2 has different UUID to sda1
md: sdb3 has different UUID to sda1
md: bind<sdb1>
md: running: <sda1><sdb1><sdc1>
md:  adding sdb2 ...
md: sdb3 has different UUID to sda2
md: bind<sdb2>
md: running: <sda2><sdb2><sdc2>
md:  adding sdb3 ...
md: bind<sdb3>
md: running: <sda3><sdb3><sdc3>
raid5: device sdb3 operational as raid disk 1
 disk 1, o:1, dev:sdb3
Cervus> dmesg | grep "sdc"
SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sdc: drive cache: write back
SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sdc: drive cache: write back
 sdc: sdc1 sdc2 sdc3
sd 2:0:0:0: Attached scsi disk sdc
md:  adding sdc1 ...
md: sdc2 has different UUID to sda1
md: sdc3 has different UUID to sda1
md: bind<sdc1>
md: running: <sda1><sdb1><sdc1>
md:  adding sdc2 ...
md: sdc3 has different UUID to sda2
md: bind<sdc2>
md: running: <sda2><sdb2><sdc2>
md:  adding sdc3 ...
md: bind<sdc3>
md: running: <sda3><sdb3><sdc3>
raid5: device sdc3 operational as raid disk 2
 disk 2, o:1, dev:sdc3
Cervus> dmesg | grep "sdd"
Cervus>

md:  adding sdc1 ...
md: sdc2 has different UUID to sda1
md: sdc3 has different UUID to sda1
md: created md0
md: bind<sdc1>
md: bind<sdb1>
md: bind<sda1>
md: running: <sda1><sdb1><sdc1>
raid1: raid set md0 active with 3 out of 4 mirrors
md: considering sda2 ...
md:  adding sda2 ...
md: sda3 has different UUID to sda2
md:  adding sdb2 ...
md: sdb3 has different UUID to sda2
md:  adding sdc2 ...
md: sdc3 has different UUID to sda2
md: created md1
md: bind<sdc2>
md: bind<sdb2>
md: bind<sda2>
md: running: <sda2><sdb2><sdc2>
raid1: raid set md1 active with 3 out of 4 mirrors
md: considering sda3 ...
md:  adding sda3 ...
md:  adding sdb3 ...
md:  adding sdc3 ...
md: created md2
md: bind<sdc3>
md: bind<sdb3>
md: bind<sda3>
md: running: <sda3><sdb3><sdc3>
raid5: device sda3 operational as raid disk 0
raid5: device sdb3 operational as raid disk 1
raid5: device sdc3 operational as raid disk 2
raid5: allocated 4212kB for md2
raid5: raid level 5 set md2 active with 3 out of 4 devices, algorithm 2
RAID5 conf printout:
 --- rd:4 wd:3
 disk 0, o:1, dev:sda3
 disk 1, o:1, dev:sdb3
 disk 2, o:1, dev:sdc3
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
ds406_synobios: module license 'Synology Inc.' taints kernel.
synobios: load, major number 201
Brand: Synology
Model: CS-406
synobios: unload
kjournald starting.  Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on md2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem).
Trying to move old root to /initrd ... okay
Freeing unused kernel memory: 124k init
Adding 393464k swap on /dev/md1.  Priority:-1 extents:1 across:393464k
NET: Registered protocol family 5
NTFS driver 2.1.27 [Flags: R/O DEBUG MODULE].
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
sd 2:0:0:0: Attached scsi generic sg2 type 0
usbcore: registered new driver usbfs
usbcore: registered new driver hub
usbcore: registered new driver snd-usb-audio
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
sk98lin: Network Device Driver v8.41.2.3
(C)Copyright 1999-2006 Marvell(R).
eth0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
      PrefPort:A  RlmtMode:Check Link State
synobios: load, major number 201
Brand: Synology
Model: CS-406
eth0: network connection up using port A
    speed:           100
    autonegotiation: yes
    duplex mode:     full
    flowctrl:        symmetric
    irq moderation:  disabled
    scatter-gather:  enabled
    tx-checksum:     enabled
    rx-checksum:     enabled
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on md2, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
ehci_hcd 0000:00:0e.2: EHCI Host Controller
ehci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0e.2: irq 17, io mem 0xbfffcf00
ehci_hcd 0000:00:0e.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd 0000:00:0e.0: OHCI Host Controller
ohci_hcd 0000:00:0e.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0e.0: irq 17, io mem 0xbfffe000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ohci_hcd 0000:00:0e.1: OHCI Host Controller
ohci_hcd 0000:00:0e.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:0e.1: irq 17, io mem 0xbfffd000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v2.3
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Cervus> dmesg | grep "sda"
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
md: considering sda1 ...
md:  adding sda1 ...
md: sda2 has different UUID to sda1
md: sda3 has different UUID to sda1
md: sdb2 has different UUID to sda1
md: sdb3 has different UUID to sda1
md: sdc2 has different UUID to sda1
md: sdc3 has different UUID to sda1
md: bind<sda1>
md: running: <sda1><sdb1><sdc1>
md: considering sda2 ...
md:  adding sda2 ...
md: sda3 has different UUID to sda2
md: sdb3 has different UUID to sda2
md: sdc3 has different UUID to sda2
md: bind<sda2>
md: running: <sda2><sdb2><sdc2>
md: considering sda3 ...
md:  adding sda3 ...
md: bind<sda3>
md: running: <sda3><sdb3><sdc3>
raid5: device sda3 operational as raid disk 0
 disk 0, o:1, dev:sda3
Cervus> dmesg | grep "sdb"
SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sdb: drive cache: write back
 sdb: sdb1 sdb2 sdb3
sd 1:0:0:0: Attached scsi disk sdb
md:  adding sdb1 ...
md: sdb2 has different UUID to sda1
md: sdb3 has different UUID to sda1
md: bind<sdb1>
md: running: <sda1><sdb1><sdc1>
md:  adding sdb2 ...
md: sdb3 has different UUID to sda2
md: bind<sdb2>
md: running: <sda2><sdb2><sdc2>
md:  adding sdb3 ...
md: bind<sdb3>
md: running: <sda3><sdb3><sdc3>
raid5: device sdb3 operational as raid disk 1
 disk 1, o:1, dev:sdb3
Cervus> dmesg | grep "sdc"
SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sdc: drive cache: write back
SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sdc: drive cache: write back
 sdc: sdc1 sdc2 sdc3
sd 2:0:0:0: Attached scsi disk sdc
md:  adding sdc1 ...
md: sdc2 has different UUID to sda1
md: sdc3 has different UUID to sda1
md: bind<sdc1>
md: running: <sda1><sdb1><sdc1>
md:  adding sdc2 ...
md: sdc3 has different UUID to sda2
md: bind<sdc2>
md: running: <sda2><sdb2><sdc2>
md:  adding sdc3 ...
md: bind<sdc3>
md: running: <sda3><sdb3><sdc3>
raid5: device sdc3 operational as raid disk 2
 disk 2, o:1, dev:sdc3
Cervus> dmesg | grep "sdd"
Cervus> mdadm --query --detail /dev/md2
/dev/md2:
        Version : 00.90.03
  Creation Time : Sat Apr  3 05:06:19 2004
     Raid Level : raid5
     Array Size : 933753792 (890.50 GiB 956.16 GB)
    Device Size : 311251264 (296.83 GiB 318.72 GB)
   Raid Devices : 4
  Total Devices : 3
Preferred Minor : 2
    Persistence : Superblock is persistent

    Update Time : Sun May 25 08:44:24 2008
          State : clean, degraded
 Active Devices : 3
Working Devices : 3
 Failed Devices : 0
  Spare Devices : 0

         Layout : left-symmetric
     Chunk Size : 64K

           UUID : 04be72db:85422703:fb099a27:f98c32f2
         Events : 0.1274042

    Number   Major   Minor   RaidDevice State
       0       8        3        0      active sync   /dev/sda3
       1       8       19        1      active sync   /dev/sdb3
       2       8       35        2      active sync   /dev/sdc3
       3       0        0        3      removed
Cervus>

[mdamen]

Je mist inderdaad één disk (welke uberhaubt niet gedetecteerd wordt)
Heb je de mogelijkheid die nieuwe disk te testen in een normale PC?
Wil nog niet gaan doemdenken, maar misschien is de sata poort stuk van je cubestation?

[Kris]

Hmm, ik ben net verhuisd en heb een setje oude pc's net gedumpt....

Nee dus... Satapoort, betekent dat dan dat elke disk die op die stekker zit niet zou werken?
Ik had al eens omgewisseld en enkel het disknummer veranderd dan.

Ik zag op het testrapport van MHD dat de disk die ik had opgestuurd stuk was (Robbin tekende af). Of zou men per ongeluk dan mijn kapotte disk teruggestuurd hebben?

Ik tast nu even in het duister, kan ik onderzoeken of het aan een sata poort ligt, en hoe dan?

[Kris]

Nog enige input wat ik moet controleren?

[Kris]

Ik was even met vakantie, maar geen reacties meer.

Hoe weet ik of de satapoort stuk is, hoe weet ik of de nieuwe geleverde schijf goed is?

Misschien moet ik maar even weer met MHD contact opnemen, want die hebben de HD opgestuurd.